Hooptech Gen2 and Adjustable TBar Combination Set for Commercial Embroidery Machines

The GEN 2 will NOT work on the Brother PRCFH5 Driver(Flat Brim).

This offer if for the Hooptech Gen 2 Cap Frame and Adjustable T Bar Framing Gage

The Hoop Tech GEN 2 Dream Frame Cap Frame is designed to work with several brands of commercial embroidery machines.  The Hoop Tech GEN 2 Dream Frame Cap Frame is one of the easiest cap frames to operate on the market.  Make more money and do more with your machine by adding a Hoop Tech Dream Frame Cap Frame.  The Hoop Tech Dream Frame Cap Frame attaches to your existing hat hoop driver.  The innovative spring steel bill retainer holds the lower front of the cap and helps to eliminate flagging.

 The Hoop Tech GEN 2 Dream Frame Cap Frame for includes:

• Lighter frame design
• Backing Clips to hold your stabilizer in place during framing.
• Internal retaining fingers for proper bill alignment
• A spring steel bill retainer that sets and holds the bill angle
• View ports to use as alignment guides during framing.
• Extensed saddle for easier installation on driver.
• Large Sewing Field

 Hoop Tech Dream Frame Cap Frame for Brother PR Series is compatible with models:

• Baby Lock 6 Needle - 599733
• Baby Lock 10 Needle - 599734
• Tajima - 599733
• Melco - 599733
• Toyota - 599733
• Barudan Advantage - 599769
• ZSK - 599733
• Meistergram - 599733
• Happy - 599757
• Highland - 599733
• SWF - 599762
• Prodigi - 599733
• Generations - 599733
• Redline - 599733

ATTENTION BROTHER PR & BABY LOCK OWNERS -

The new “GEN 2” will turn your (6) & (10) needle machine into a REAL cap sewing machine. The new bill holding strap holds down the bill so you can get closer to the needles than ever before, for a much larger sewing field.

For PR & Baby Lock owners, the “GEN 2” comes with a specially designed override bracket that attaches to your cap frame drive bar with one of the 2 thumb screws, and allows you to sew a larger sewing field and also increases the stitching speed. (Just click here to see how easy it is to set up your machine for the dream frame)

The maximum height you can stitch is approximately up to 4" and 5.5"- 6" left to right and as close to 1/2"-5/8" from the bill. However, we do not recommend trying to embroider to the maximum sewing areas depending on the capabilities of your machine. Sewing too close to the top of the cap or too close to the bill could compromise the quality of your stitch. A more realistic measurement would be somewhere between 2" to 2.5" high and 5" to 5.5" across without losing registration.

Note: You need to already own the Brother hat jig and driver for this item to work. 

The patented HoopTech Adjustable T Bar Framing Gage features the exclusive T–Bar Tensioning Arm. This tensioning arm, on the HoopTech Adjustable T Bar Framing Gage gives even the inexperienced cap framer the ability to frame a cap tight, even low profile un-constructed caps. Once you try HoopTech Adjustable T Bar Framing Gage, you’ll be amazed at how easy it can be to frame a cap. The EMS / Hoop Tech T-BAR framing gauge is the first step to properly framing up a finished cap. The T-BAR Framing Gage featuring the exclusive T-Bar Tensioning Arm, allowing the embroiderer to stretch the front panels of the cap against the top of the gauge so that when the cap is clamped by the cap frame it is held in the ideal position for sewing. The framing gauge with its lever arm, gives the cap framer a 10 to 1 mechanical advantage when getting the cap to lay flat before sewing. This saves a great deal of energy when framing up large orders. Only Hoop Tech has the patented Tensioning Arm.